[ays_quiz id="20"]
Free AMPP CIP Level II online practice exam quiz February 14, 2025March 17, 2025 Pass Guaranteed NACE CIP Level-1 Exam or get full refund guaranteed 1 Free AMPP CIP Level II online practice exam quiz 1 / 25 1) When completing the Final Inspection report, the Inspector should write the report using: Language that only technical experts would understand Language that the most would understand Language that only those in the project would understand Language that another NACE Inspector would understand 2 / 25 2) When using electrostatic spray equipment, what is essential for safety? Ensuring proper ventilation Grounding all conductive materials Wearing rubber gloves Ignoring static discharge concerns 3 / 25 3) What is a common requirement before applying any repair coating? Surface must be wet Must have a clean surface Surface must be painted Surface must be cold 4 / 25 4) What is the main cause of solvent blistering in coatings? Poor ventilation during application Excessive DFT per coat Inadequate surface preparation All of the above 5 / 25 5) Which layer in hot-dip galvanizing contains 94% zinc? ZETA Delta Gamma ETA 6 / 25 6) The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of Urethanes Inorganic zincs Epoxies Powder coatings 7 / 25 7) What must be ensured before beginning waterjetting operations? The area is well-lit The work area is barricaded and safe The equipment is painted The operators are well-rested 8 / 25 8) When observing fabrication defects, the NACE Inspector should: Require they be corrected prior to coating Consult the specification to determine how they should be treated Stop the job immediately Write an NCR and call the fabricator 9 / 25 9) What is the typical temperature range for the sherardizing process? 100-200°C (212-392°F) 300-400°C (572-752°F) 500-600°C (932-1112°F) 700-800°C (1292-1472°F) 10 / 25 10) What type of paint should be used on galvanized surfaces? Any type of paint A wash primer or special tie coat Oil-based paint Water-based paint 11 / 25 11) What is the function of insulation half shells in pipeline applications? To enhance aesthetics To provide thermal insulation To reduce weight To prevent corrosion 12 / 25 12) What is the main focus of the Shipboard Corrosion Assessment Training (S-CAT)? Aesthetic evaluation Corrosion control knowledge Financial management Legal compliance 13 / 25 13) Pre-cleaning of work pieces will NOT remove Snow, ice or water Oil or grease Dirt Mill scale 14 / 25 14) What factors can affect the time a surface retains its desired condition before coating? Ambient temperature Surface cleanliness Humidity levels All of the above 15 / 25 15) Which of the following techniques is used in maintenance coating to ensure smooth transitions? Curling Feathering Layering Stacking 16 / 25 16) Which layer in a three-layer polyethylene (3LPE) coating is applied directly to the steel substrate? Top layer Primer layer Fusion Bonded Epoxy layer Adhesive layer 17 / 25 17) What is an important factor for the application of acrylic coatings? Low humidity High humidity Excessive heat Cold temperatures 18 / 25 18) What is the main advantage of using epoxy coatings on concrete? High flexibility Excellent adhesion and chemical resistance Low cost Easy application 19 / 25 19) Which of the following is a requirement for preparing galvanized surfaces? They should be heated They must be allowed to weather They must be coated immediately They should be painted without cleaning 20 / 25 20) You can use magnifiers to examine all of the following EXCEPT: Surface profile Surface cleanliness Blisters Mill scale 21 / 25 21) What is the best practice if a pre-cure is performed during lining application? Continue with the final cure Repair and then complete the final cure Ignore the results of the pre-cure Document the findings only 22 / 25 22) What is the primary purpose of industry standards? To ensure aesthetic appeal To establish uniform criteria and practices To dictate product pricing To limit competition 23 / 25 23) What is a common failure mode in solvent-evaporation cured coatings? Excessive thickness Poor adhesion Incomplete curing All of the above 24 / 25 24) The Concrete Repair Institute’s comparators can be used to assess: Surface cleanliness prior to coating Surface profile prior to coating Contamination levels prior to coating Compressive and tensile strength prior to coating 25 / 25 25) What is the main purpose of using sealers on thermal spray coatings? To enhance aesthetics To improve adhesion To prevent corrosion To increase thickness Your score is LinkedIn Facebook Twitter VKontakte
