FREE NACE AMPP CIP Level 1 Practice Exam Quiz

Free Online Quiz for NACE/ AMPP CIP Level 1 Exam

Are you preparing for the NACE/AMPP CIP Level 1 Exam? Whether you’re a seasoned professional or just starting your journey in Coating inspection, mastering the study material is crucial for success. To help you on your path, we’re excited to offer a Free Online Quiz designed specifically for the CIP Level 1 Theory Exam

Pass Guaranteed NACE CIP Level-1 Exam

This interactive quiz not only tests your knowledge but also familiarizes you with the exam format, allowing you to identify areas where you may need further study. With a range of questions covering essential topics, our quiz is an invaluable resource that can enhance your understanding and boost your confidence. Ready to take the next step in your career?

FREE NACE AMPP CIP Level 1 Practice Exam Quiz

Use full screen mode for improved experience.

1 / 25

1. A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%. What wet film thickness (WFT) was applied?

A. 5 to 6 mils (125 to 150 microns)

B. 10 to 12 mils (250 to 300 microns)

C. 8 to 10 mils (200 to 250 microns)

D. 6 to 7 mils (150 to 175 microns)

2 / 25

2. Safety Data Sheets must be carefully reviewed by:

A. The Application personnel

B. The Inspection personnel

C. The Owner's personnel

D. All personnel involved in the job

3 / 25

3. ISO SA 3 is directly equivalent to:

A. NACE No. 1/SSPC SP 5

B. NACE No. 2/SSPC SP 10

C. NACE No. 3/SSPC SP 6

D. None of the above

4 / 25

4. NACE SSPC SP 2 is for:

A. Hand tools

B. Power tools

C. Bare metal

D. Commerical power tool cleaning

5 / 25

5. _________ refer to the prevailing, and uncontrolled atmospheric and weather conditionssurrounding a structure.

A. Environmental conditions

B. ambientconditions

C. A & B

D. surface temperature

6 / 25

6. Nozzle pressure for manual blast cleaning is generally accepted to be:

A. 65 to 90 psi

B. 90 to 100 psi

C. 130 to 150 psi

D. 130 psi and above

7 / 25

7. You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owner’s representative has supplied you with the local code governing the removal and disposal of lead-based coatings, but you have difficulty understanding it. As a NACE CIP Level 1 Inspector, your preferred course of action is to:

A. Carefully review the document and do the best you can

B. Minimize your lack of understanding and proceed

C. Advise the owner's representative of your lack of knowledge

D. Hire a third party to assist you in understanding the document

8 / 25

8. Daily reports are important because:

A. Inspectors rarely change on a project

B. Management uses them to make personnel decisions

C. The information impacts future projects

D. The information aids communication with supervisors

9 / 25

9. Tight mill scale can cause

A. Early coating failure

B. Later coating failure

C. corrosion after coating

D. All of the above

10 / 25

10. The primary difference between Non-Convertible vs. Convertible coatings is:

A. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do

B. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do

C. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not

D. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not

11 / 25

11. Which one of the following documents is the best source for coating technical data:

A. Safety Data Sheet

B. Technical Data Sheet

C. Application Guidelines

D. Specification

12 / 25

12. Due to a previous premature coating failure, the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three-coat system at the applicator’s cost. The owner has offered you the job as the NACE CIP Level 1 Coating Inspector, expecting you to be his “insurance policy” for this job. Your preferred FIRST course of action is to:

A. Review the Product Data Sheets and meet with the Coating Applicator prior to the pre-job meeting

B. Review the Product Data Sheets and conduct a walk-thru of the job site prior to the pre-job conference

C. Purchase Professional Liability Insurance prior to job commencement

D. Meet with the owner and explain your limitations and concerns prior to accepting the assignment

13 / 25

13. A magnetic pull-off type gauge is a good choice when:

A. Accuracy is not required

B. When an intrinsically safe tool is required

C. Performing an adhesion test

D. When working on non-ferrous metals

14 / 25

14. High humidity in the air during coating application can cause which of the following:

A. Solvent entrapment

B. Rapid solvent evaporation

C. Solvent combustion

D. Shorter induction times

15 / 25

15. In a non-convertible coating, the role of the primary solvent is to:

A. To make the coating flow out better

B. To dissolve the resin

C. To promote faster cure

D. To control the evaporation rate

16 / 25

16. ISO 8501-1 rust grade-D for unpainted steel is:

A. Steel surface largely covered with adherent mill scale; little if any rust

B. Steel surface which has begun to rust and from which the mill scale has begun to flake

C. Steel surface on which the mill scale has rusted away or from which it can be scraped but with slight pitting visible under normal vision

D. Steel surface on which the mill scale has rusted away on which general is pitting visible under normal vision

17 / 25

17. When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:

A. Go with the majority opinion

B. Never change his/her mind

C. Achieve consensus through negotiation

D. Call the supervisor

18 / 25

18. You are an inspector on a project where SSPC SP 3 is specified. What sort of tools should you expect the Contractor to use to achieve the standard?

A. Abrasive blast nozzles

B. Power tools

C. Hand tools

D. Airless spray equipment

19 / 25

19. Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:

A. Using a damaged gauge

B. Dragging a gauge through wet coating

C. Placing the gauge along the longitudinal axis

D. Answer: AB

20 / 25

20. The NACE Inspector should perform tests for soluble salts:

A. Prior to surface preparation

B. After surface preparation

C. Prior to coating application

D. When specified

21 / 25

21. NACE No. 3 standard is for:

A. White metal cleaning

B. Near white metal cleaning

C. Commercial blast cleaning

D. Brush off blast cleaning

E. Industrial blast cleaning

22 / 25

22. SSPC SP 1 identifies the use of:

A. Organic solvents

B. Inorganic solvents

C. Biodegradable detergents

D. A wide variety of materials

23 / 25

23. An Inspector should change position when:

A. The Inspector is convinced by verifiable facts

B. Only when directed by the supervisor

C. The Inspector's position is not the majority…

D. The Owner can save some money by the change

24 / 25

24. Freshly galvanized steel should be coated_____ to prevent formation of zinc carbonate salts.

A. Within 20 hours

B. Within 12 hours

C. Within 24 hours

D. Within 36 hours

25 / 25

25. Which type of substrate requires special consideration when selecting abrasives for surfacepreparation?

A. Rusted Steel

B. Carbon Steel

C. Stainless Steel

D. Painted Steel

Your score is

Looking for a Free Practice Test for the AMPP/NACE CIP Level 1 Exam?

Take a Free NACE CIP Level 1 Exam Practice Test Today!

If you’re seeking a way to prepare for the AMPP/NACE CIP Level 1 Exam, you’ve come to the right place! Here, you can access a Free Online AMPP/NACE CIP Level 1 Exam Practice Test designed to help you enhance your score. Our platform makes it easy to learn everything you need to know about the NACE CIP Level 1 quickly and effectively.

You can also purchase our Premium Package for the CIP Level 1 Examination, which offers an extensive collection of over 1,000 questions designed to cover all the key topics included in the exam. This package not only provides depth and variety in practice questions but also includes 10 free mock exams that closely simulate actual exam conditions.

Why Choose Our Premium Package?

Comprehensive Coverage: With over 1,000 questions, you’ll have access to a wide range of topics, ensuring you’re well-versed in all areas relevant to the CIP Level 1 Exam.
Real Exam Simulation: Our mock exams are specifically designed to mimic the format and timing of the actual test, helping you familiarize yourself with the exam environment. This realistic experience can reduce anxiety and improve your performance on exam day.
Detailed Explanations: Each question in the Premium Package comes with thorough explanations, allowing you to understand not just the correct answers but also the reasoning behind them. This will help reinforce your learning and clarify any doubts.
Flexible Learning: You can study at your own pace, revisiting challenging topics and taking mock exams whenever you choose. This flexibility allows you to tailor your study plan to fit your schedule and learning style.
Continuous Updates: We regularly update our question bank to reflect the most current industry standards and practices, ensuring that you’re always studying the most relevant material.

Invest in Your Success

By choosing our Premium Package, you’re making a smart investment in your professional development. With our resources, you’ll be better equipped to tackle the challenges of the CPI Level 1 Exam and advance your career in the coating inspection field.

Don’t miss out on this opportunity to enhance your preparation—purchase the Premium Package today and take a significant step toward achieving your certification goals!

Free Online Quiz for NACE/ AMPP CIP Level 1 Exam

Looking for a Free Practice Test for the AMPP/NACE CIP Level 1 Exam?

Why Choose Our Premium Package?

Invest in Your Success

Leave a Reply Cancel reply